Tag Archives: symbol

Service oil reset Mercedes Benz C-Class

Leave a reply

Reset service light indicator, engine oil life Mercedes Benz C-Class, year 1997-2000 reset instructions:

How to reset oil service light Mercedes Benz C-Class. From year: 1997-2000
*Diagnostic Reset Tool Required (please refer to TOOLS page)
Manual Reset:
Turn key in steering lock to position 2.
Within 4 seconds press 0 button twice.
The present status for days or distance displays, within 10 seconds turn the electroninc key in steering lock to position 0.
Press and hold 0 button while turning electronic key in steering loack to position 2 again. The present status for days or distance displays once more. Continue to hold 0 button for approximately 10 seconds until a signal sounds and the display shows 10 000 (15000KM) for approximately 10 seconds.
Release 0 button, the status is reset.
2001
Turn key in steering lock to position 2.
Call up the trip odometer and main odometer: press either of the lower two buttons on the left hand side of steering wheel until the display appears.
Press either of the top buttons on steering wheel (arrows) until the FSS indicator appears.
Press R button on the instrument cluster for 2-4 seconds.
The display reads “DO YOU WANT TO RESET SERVICE INTERVAL?” confirm by pressing R button.
Press and hold the R button on instrument cluster again until signal sounds. Message will res “SERVICE INTERVAL HAS BEEN RESET”.
2002
Switch ignition on.
Repeatedly press the system selection button (bottom button located on left hand side of steering wheel) until the service symbol is displayed in the multifunction display.
Repeatedly press the SCROLL FORWARD/BACK button (top button on left hand side of steering wheel) until the service symbol is displayed in the multifunction display.
“DO YOU WANT TO RESET THE SERVICE INTERVAL?” appears, confirm that you see the message by holding down the RESET (R) button until you hear a signal.
The reset interval is set.
2003
Turn on the ignition (standard display of the control system appears).
Press SYSTEM button on the multifunction steering wheel until FSS indicator with service symbol and the service deadline appear on display.
Message appears on display “DO YOU WANT TO RESET THE SERVICE INTERVAL?” Confirm by pressing RESET (R) button until you hear a signal (approximately 4 seconds).
2004
Turn on the ignition (standard display of the control system appears).
Press button (UP arrow) or (DOWN arrow) on the multifunction steering wheel until the FSS indicator appears in the display.
Press RESET button for about 3 seconds until this message appears: “SERVICE INTERVAL? RESET WITH R BUTTON FOR 3 SEC.”
To confirm press RESET button until you hear a signal. The service indicator now displays the reset interval.

Service oil reset Nissan Cube

Leave a reply

2009-2010
Turn the ignition to run (one position before starting engine). The maintenance information (the wrench symbol and distance to change a maintenance item) comes on for about 5 seconds and then turns off.
Push the trip computer mode switch A for 3 seconds while the wrench symbol and maintenance information are displayed. The symbol and distance display will start flashing and the display shows the current interval (ie. 5000KM).
Push the switch A to increase the interval distance. Each step increases the interval by 1000km. The interval distance can be set up to 30000km after the display returns to 0.
If no further action is made, the display returns to the previous mode and the new interval is set. If the interval distance is set to 0, the display will skip the maintenance information when the ignition is placed in run or start mode.

Reset the service counter in car (seat altea)

Leave a reply

Switch ignition OFF
Press and hold button A (underneath rev counter)
Switch ignition ON
Release button A
A spanner symbol will be displayed
Turn button A clockwise
Switch ignition OFF

Reset Your Service Light Peugeot

Leave a reply

If that spanner symbol has come up on your dashboard then it’s time your car was due a service. The symbol is just a periodic reminder, it doesn’t actually come up to denote a fault – the ‘check engine’ symbol does that.

If you service the car yourself and want to reset it or your garage has forgotten to reset it, you can do it yourself quite easily with the following simple steps:

This will work with the following models:

Peugeot 106 (1999 on)
Peugeot 206 (1998 on)
Peugeot 306 (1996 on)
Peugeot 307 (1996 on)
Peugeot 406 (1998 on)
Peugeot 607 (2000 on)
Peugeot 806 (1999 on)
Peugeot Expert (1999 on)
Peugeot 807 (2002 on)
Peugeot Partner (1999 on)
Peugeot Boxer (2002 on)

Procedure to Reset Peugeot Service Light as follows:

1. Switch the Ignition Off

2. Press and hold the tripmeter (mileage reset) button on the dash

3. Now switch the ignition to the ON position

4. Keep the button pressed for 10 seconds

5. The display will read ‘0’ and the service symbol will extinguish. Job done.

Service light reset Renault Clio, Laguna 2

Leave a reply

Service light reset Renault Clio (2005-present), Espace 4 (2003-present), Laguna II (2001-2007), Megane II (2002-2009), Scenic II (2003-2009), Twingo (2007-present), Vel Satis (2002-2009)

The service light on these vehicles is usually a spanner / wrench symbol. To reset that indicator:

Turn the Ignition ON (position 2) but do not start the engine
(On cars with keycard ignition, insert the card, then press and hold the start button for 5 seconds to turn on the dash cluster)
Press the button on the end of the wiper stalk repeatedly until the spanner symbol and miles to service appears on the display
(Some models have 2 buttons, which cycle through the options in opposite directions – either button can be used in this case)
Press and hold the button
The display will now change to the new service interval and start flashing
Keep holding the button until the display stops flashing
Release the button