Tag Archives: signal

Reset service light oil life indicator dashboard Chevrolet Cruze

Leave a reply

How do you reset maintenance light, reset service light indicator Chevrolet Cruze, year 2013, 2014, 2015. For reset maintenance light and that can be made manually by use button on car dash board.

Reset service light indicator, engine oil life Chevrolet Cruze, year 2013, 2014, 2015 oil reset instructions:

  1. Turn the ignition to run (one position before starting engine).
  2. Press the DIC menu button on the turn signal lever to enter the vehicle information menu. Use the thumbwheel to scroll through the menu items until you reach REMAINING OIL LIFE.
  3. Press the SET/CLR button to reset the oil life to 100%. When prompted select YES or NO. Press the SET/CLR button to confirm.
  4. Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil reset service light indicator Chevrolet Cruze

Leave a reply

How do you reset maintenance light, reset service light indicator Chevrolet Cruze, year 2012. For reset maintenance light and that can be made manually by use button on car dash board.

  1. Turn the ignition to run (one position before starting engine).
  2. Press the DIC menu button on the turn signal lever to enter the vehicle information menu. Use the thumbwheel to scroll through the menu items until you reach REMAINING OIL LIFE.
  3. Press the SET/CLR button to reset the oil life to 100%. When prompted, use the thumbwheel to select YES or NO. Press the SET/CLR button to confirm.
  4. Turn the ignition off and then start the engine to verify the indicator has been reset.

Reset enhanced accident response system Fiat 500

Leave a reply

Reset enhanced accident response system Fiat 500. From year: 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014.

How to reset enhanced accident response system Fiat 500.

In the event of an impact causing air bag deployment, if the communication network remains intact, and the power remains intact, depending on the nature of theevent, the ORC will determine whether to have the Enhanced Accident Response System perform the following functions:

  • Cut off fuel to the engine.
  • Flash hazard lights as long as the battery has power or until the ignition key is turned off.
  • Turn on the interior lights, which remain on as long as the battery has power or until the ignition key is removed.
  • Unlock the doors automatically.
  • After the event occurs, when the system is active, the message Fuel Cutoff See Handbook is displayed. Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.

System reset procedure.

After an impact causing air bag deployment, the left and right turn signal lights, located in the instrument panel cluster, will both be blinking, until the ignition is turned off. In order to move your vehicle to the side of the road you must follow the system reset procedure.

  1. Turn ignition OFF. Turn signal switch must be placed in neutral state.
  2. Turn ignition ON. Customer will see left turn light is OFF. Right turn light blinks.
  3. Turn right turn signal switch ON. Customer will see – right turn light is ON solid. Left turn light blinks.
  4. Turn left turn signal switch ON. Customer will see, left turn light is ON solid. Right turn light blinks.
  5. Turn right turn signal switch ON. Customer will see, right turn light is ON solid. Left turn light blinks.
  6. Turn left turn signal switch ON. Customer will see, Left turn light is ON solid. Right turn light is ON solid.
  7. Turn left turn signal switch OFF. Turn signal switch must be placed in neutral state. Customer will see, left turn light is OFF. Right turn light is OFF.
  8. Turn ignition OFF. Customer will see, system is now reset and the engine may be started.
  9. Turn hazard flashers OFF (manually).
  10. If a reset procedure step is not completed within 45 seconds, then the turn signal lights will turn off and the reset procedure must be performed again in order to be successful.

If a deployment occurs.

The advanced front Air Bags are designed to deflate immediately after deployment.

Front and/or side air bags will not deploy in all collisions. This does not mean something is wrong with the air bag system.

If you do have a collision which deploys the air bags, any or all of the following may occur:

  • The nylon air bag material may sometimes cause abrasions and/or skin reddening to the driver and front passenger as the air bags deploy and unfold. The abrasions are similar to friction rope burns or those you might get sliding along a carpet or gymnasium floor. They are not caused by contact with chemicals. They are not permanent and normally heal quickly. However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately.
  • As the air bags deflate, you may see some smoke-like particles. The particles are a normal by-product of the process that generates the non-toxic gas used for air bag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water. For nose orthroat irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s instructions for cleaning.

Do not drive your vehicle after the air bags have deployed. If you are involved in another collision, the air bags will not be in place to protect you.

Deployed air bags and seat belt pretensioners cannot protect you in another collision. Have the air bags, seat belt pretensioners, and the front seat belt retractor assemblies replaced by an authorized dealer immediately. Also, have the Occupant Restraint Controller (ORC) system serviced as well.

Reset replace key battery message Saab 9-3

Leave a reply

How to reset replace key battery message Saab 9-3 first generation.

Reset replace key battery message Saab 9-3 first generation. From year: 1998, 1999, 2000, 2001, 2002.

 

  • Enter the key in the ignition and turn it until the lights on the dashboard go on, one position befor you start the engine.
  • The replace key battery message light cannot be removed by pressing CLEAR button.
  • To reset this warning light push the brake pedal to clear.

Changing the remote-control battery. When the battery voltage in the remote control falls below a predetermined level the SID will issue the following message: REPLACE KEY BATTERY. Press the CLEAR button on the SID to acknowledge this message. You must then replace the battery without delay to avoid malfunctions. The life of the battery is 4-5 years. After changing the battery you must press the unlocking button of the remote control four times (or until the door locks cycle) while the car is within the range of the remote control in order for the control module to recognize the remote.

Battery for remote control. The battery for the remote control will normally have a life of 4-5 years. When the battery needs changing, ”REPLACE KEY BATTERY” will appear on the SID. After fitting a new battery, press the unlock button on the remote ontrol at least four times in succession, so that the car alarm can recognize the signals from the transmitter. If the remote control has been exposed to very low temperatures, it may not function properly. If this happens, warm it in your hands for a few minutes. If the remote control is not working, it may be because the code signal has not been synchronized with that in the control module for the car alarm. To rectify this, press the unlock button on the remote control at least four times in quick succession. When it is recognized, the door locks will cycle.

Reset tire pressure warning light Toyota Rav4 XA40

Leave a reply

Reset tire pressure warning light Toyota Rav4 XA40 fourth generation. From year: 2013, 2014.

How to reset oil service light Toyota Rav4, 3 generation XA30, 4 generation.

How to initialize the tire pressure warning system.

  1. Park the vehicle in a safe place and turn the engine switch to the “LOCK” position (vehicles without a smart key system) or off (vehicles with a smart key system). Initialization cannot be performed while the vehicle is moving.
  2. Adjust the tire inflation pressure to the specified cold tire inflation pressure level. Make sure to adjust the tire pressure to the specified cold tire inflation pressure level. The tire pressure warning system will operate based on this pressure level.
  3. Turn the engine switch to the “ON” position (vehicles without a smart key system) or IGNITION ON mode (vehicles with a smart key system).
  4. Press and hold the tire pressure warning reset switch until the tire pressure warning light blinks slowly 3 times.
  5. Reset-tire-pressure-warning-light-Toyota-Rav4-XA40
  6. Vehicles without a smart key system: Wait for a few minutes with the engine switch in the “ON” position and then turn the engine switch to the “ACC” or “LOCK” position. Vehicles with a smart key system: Wait for a few minutes with the engine switch in IGNITION ON mode and then turn the engine switch off.

Registering ID codes Toyota Rav 4.

The tire pressure warning valve and transmitter is equipped with a unique ID code. When replacing a tire pressure warning valve and transmitter, it is necessary to register the ID code. Have the ID code registered by your Toyota dealer.

When to replace your vehicle’s tires. Tires should be replaced if:

  • You have tire damage such as cuts, splits, cracks deep enough to expose the fabric, and bulges indicating internal damage.
  • A tire goes flat repeatedly or cannot be properly repaired due to the size or location of a cut or other damage.

If you are not sure, consult with your Toyota dealer.

Replacing tires and wheels (vehicles with the tire pressure warning system).

If the ID code of the tire pressure warning valve and transmitter is not registered, the tire pressure warning system will not work properly. After driving for about 20 minutes, the tire pressure warning light blinks for 1 minute and stays on to indicate a system malfunction.

Tire life Toyota Rav4.

Any tire over 6 years old must be checked by a qualified technician even if it has seldom or never been used or damage is not obvious.

Routine tire inflation pressure checks (vehicles with the tire pressure warning system).

The tire pressure warning system does not replace routine tire inflation pressure checks. Make sure to check tire inflation pressure as part of your routine of daily vehicle checks.

Situations in which the tire pressure warning system may not operate properly (if equipped).

In the following cases, the tire pressure warning system may not operate properly.

  • If non-genuine Toyota wheels are used.
  • A tire has been replaced with a tire that is not an OE (Original Equipment) tire.
  • A tire has been replaced with a tire that is not of the specified size.
  • Tire chains etc. are equipped.
  • Lock nuts are equipped.
  • An auxiliary-supported run-flat tire is equipped.
  • If a window tint that affects the radio wave signals is installed.
  • If there is a lot of snow or ice on the vehicle, particularly around the wheels or wheel housings.
  • If the tire inflation pressure is extremely higher than the specified level.
  • If the spare tire is in a location subject to poor radio wave signal reception.
  • If a large metallic object which can interfere with signal reception is put in

*: Vehicles with a full-size spare tire only

Performance may be affected in the following situations.

  • Near a TV tower, electric power plant, gas station, radio station, large display, airport or other facility that generates strong radio waves or electrical noise.
  • When carrying a portable radio, cellular phone, cordless phone or other wireless communication device.

When the vehicle is parked, the time taken for the warning to start or go off could be extended.
When tire inflation pressure declines rapidly for example when a tire has burst, the warning may not function.