Tag Archives: reset switch

Toyota Land Cruiser 200 series reset tire pressure warning light

Leave a reply

How to reset tire pressure warning system Toyota Land Cruiser 200 series.

Reset tire pressure warning light Toyota Land Cruiser 200 series. From year: 2008, 2009, 2010, 2011, 2012, 2013, 2014.

  1. Park the vehicle in safe place and turn the “ENGINE START STOP” switch to OFF mode. While the vehicle is moving, initialization is not performed.
  2. While the vehicle is moving, initialization is not performed. Make sure to adjust the tire pressure to the specified cold tire inflation pressure level. The tire pressure warning system will operate based on this pressure level.
  3. Turn the “ENGINE START STOP” switch to IGNITION ON mode.
  4. Press and hold the tire pressure warning reset switch until the tire pressure warning light blinks slowly three times and the message “TIRE PRESSURE RESET PROCEEDING” appears on the multi-information display.
  5. Wait for a few minutes with the IGNITION ON mode, and then turn the “ENGINE START STOP” switch to OFF mode.
  6. The tire pressure warning valve and transmitter is equipped with a unique ID code. When replacing a tire pressure warning valve and transmitter, it is necessary to register the ID code of tire pressure warning valve and transmitter. Have the ID code registered by your Toyota dealer.

Any tire over 6 years old must be checked by a qualified technician even if they have seldom or never been used or damage is not obvious.

If you press the tire pressure reset switch accidentally.

If initialization is performed, adjust the tire inflation pressure to the specified level and initialize the tire pressure warning system again.

When the initialization of the tire pressure warning system has failed.

Initialization can be completed in a few minutes. However, in the following cases, the settings have not been recorded and the system will not operate properly. If repeated attempts to record tire inflation pressure settings are unsuccessful, have the vehicle inspected by your Toyota dealer.

When operating the tire pressure warning reset switch, the warning light does not flash 3 times and the setting message does not appear on the multi-information display.

Reset tire pressure warning light Toyota FJ Cruiser

Leave a reply

How to reset tire pressure warning light Toyota FJ Cruiser.
Reset tire pressure warning light Toyota FJ Cruiser. From year: 2012, 2013, 2014.

How to initialize the tire pressure warning system.

  • Park the vehicle in safe place and turn the engine switch to the LOCK position. While the vehicle is moving, initialization is not performed.
  • Adjust the tire inflation pressure to the specified cold tire inflation pressure level. Make sure to adjust the tire pressure to the specified cold tire inflation pressure level. The tire pressure warning system will operate based on this pressure level.
  • Turn the engine switch to the ON position.
  • Press and hold the tire pressure warning reset switch until the tire pressure warning light blinks slowly 3 times.

Reset-tire-pressure-warning-light-Toyota-FJ-Cruiser

  • Wait for a few minutes with the engine switch on, and then turn the engine switch to the ACC or LOCK position.

The tire pressure warning valve and transmitter is equipped with a unique ID code. When replacing a tire pressure warning valve and transmitter, it is necessary to register the ID code of tire pressure warning valve and transmitter. Have the ID code registered by your Toyota dealer.

When to replace your Toyota FJ Cruiser tires.

Tires should be replaced if:

You have tire damage such as cuts, splits, cracks deep enough to expose the fabric or bulges indicating internal damage.
A tire goes flat repeatedly or cannot be properly repaired due to the size or location of a cut or other damage.
If you are not sure, consult with your Toyota dealer.

Replacing tires and wheels on your Toyota FJ Cruiser.

If the ID code of the tire pressure warning valve and transmitter is not registered, the tire pressure warning system will not work properly. After driving for about 20 minutes, the tire pressure warning light blinks for 1 minute and stays on to indicate a system malfunction.

Tire life.

Any tire over 6 years old must be checked by a qualified technician even if they have seldom or never been used or damage is not obvious.

If the tread wears down below 0.16 in. (4 mm) on snow tires.

The effectiveness of snow tires is lost.

Reset tire pressure warning light Toyota Solara 2 generation

Leave a reply

Reset tire pressure warning light Toyota Solara 2 generation. From year: 2004, 2005, 2006, 2007, 2008.

How to reset tire pressure warning light Toyota Solara second generation.

Reset-tire-pressure-warning-light-Toyota-Solara-2-generation

This light warns that the tire pressure of one or more of your tires (including ground spare tire) is low. The light comes on when the ignition key is turned to the “ON” position. It goes off after a few seconds. This indicates that the tire pressure warning system is functioning properly. If the warning light comes on, stop your vehicle in a safe place as soon as possible and check that the inflation pressure of all tires (including ground spare tire) is as specified on the tire and loading information label.

The light should go off a few minutes after the tire pressure is adjusted.

If the warning light comes on after blinking for 1 minute, the tire pressure warning system may be malfunctioning. Contact your Toyota dealer.

TIRE PRESSURE WARNING RESET SWITCH.

When initializing the system, the present tire inflation pressure is stored as standard. The tire pressure warning system determines decreased air pressure by comparing the present and the standard tire inflation pressures. When you change the set tire inflation pressure, it is necessary to initialize the tire pressure warning system.

  • When changing the tire size.
  • When rotating the tire on vehicles differing with front and rear tire inflation pressure.

To initialize the system, perform the following:

  1. Park the vehicle in a safe place and turn the ignition key to “OFF” position.
  2. Adjust the pressure of all the installed tires to the specified cold tire inflation pressure level.
  3. Turn the ignition key to the “ON” position.
  4. Push and hold the tire pressure warning reset switch until the tire pressure warning light blinks slowly three times.
  5. Leave for a few minutes with the ignition key in “ON” position, and then turn the ignition key to “OFF” position.

If you push the tire pressure reset switch while vehicle is moving, initialization is not performed. If you push the tire pressure reset switch accidentally and initialization is performed, adjust the tire inflation pressure to the specified level and initialize the system again.

If the tire pressure warning light does not blink slowly three times when you push and hold the reset switch, initialization has failed and the tire pressure warning system may not work properly. In this case, initialize the system again. If initialization cannot be performed, have the system checked at your Toyota dealer.

Do not push the reset switch without first adjusting the tire inflation pressure to the specified level. Otherwise, the tire pressure warning light may not come on even if the tire inflation pressure is low, or it may come on when the tire inflation pressure is actually normal.

That it is the full procedure how to reset tire pressure warning light Toyota Solara second generation. If you like to reset any maintenance oil light after an oil change. Or reset check engine light, airbag light, inspection key or insp errors when maint reqd, for Toyota cars. Or any warning light for service reminder which appears on the display. Write in the search box the car name for which you want to find information, and find how to reset other service reminders by yourself.

Reset the service oil light on Jaguar S-type

Leave a reply

How do you reset maintenance light, reset service light indicator Jaguar S-type. For reset maintenance light and that can be made manually by use button on car dash board.

Reset service light indicator, engine oil life Jaguar S-type, oil reset instructions:

Here’s how to do it yourself in no time works on a few different Jags….

Service Light Reset Instructions:

1 . Insert key into ignition.
2 . Press and hold the Reset switch (located on the Trip Computer Switchpack ).
3 . NOTE: The reset switch has to be released immediately after the ignition is switched ‘ON’. This is critical to enable the rest of the procedure.
Turn the key to Ignition position II and at the point of entering Ignition position II (i.e when a click is heard), instantaneously release the Reset switch.
4 . Wait one second.
5 . Press and hold the Trip switch (located on the end of the left-hand side stalk).
6 . Wait one second.
7 . Press and hold the Reset switch (whilst still holding the Trip switch).
8 . The cluster should display (within three seconds) the warning message ‘RESETTING SERVICE MODE’.
9 . Keep both buttons pressed until the warning message changes to ‘SERVICE MODE RESET’ (after ten seconds).
10 . Once the message is displayed the buttons may be released — sequence is now complete.
11 . If a Service Required message was displayed prior to the reset sequence, cycle the ignition to ‘Off’ and then back to Ignition position II and check that the message is no longer displayed.

Service oil reset Mercedes Benz SLK – Class

Leave a reply

Reset service light indicator, engine oil life Mercedes-Benz SLK – Class, year: 1998-1999, oil reset instructions:

Manual Reset:
Turn key in steering lock to position 2.
Within 4 seconds press button (1) left of speedometer twice.
The present status for days or distance displays, within 10 seconds turn key in steering lock to position O.
Press and hold button (1), while turning key in steering lock to position 2 again. The present status for days or distance displays once more.
Continue to hold button (1) for approximately 10 seconds until a signal sounds and the display shows 10 000 mils or 15 000km. Release button (1).

2000-2001

Manual Reset:
Switch ignition on and immediately press knob to left of speedometer twice within 4 seconds.
Present status for days or distance is now displayed. Within 10 seconds, turn key in steering wheel lock to position 0.
Press and hold button to the left of speedometer, while turning key in steering lock to position 2 again. The present status for days or distance is displayed again. Continue to hold button until you hear a signal (approximately 10 seconds).
Release button.
Service interval displays the reset interval.

2002-2004
Switch ignition on and immediately press knob to left of speedometer twice within 1 second.
Present status for days or distance is now displayed. Within 10 seconds, turn key in steering wheel lock to position 0.
Press and hold button to the left of speedometer, while turning key in steering lock to position 2 again. The present status for days or distance is displayed again. Continue to hold button until you hear a signal (approximately 10 seconds).
Release button.
Service interval displays the reset interval.