How do you reset oil service light Cadillac Allante. From years: 1989, 1990, 1991, 1992, 1993.
Reset oil service light Cadillac Allante. From years: 1989, 1990, 1991, 1992, 1993.
How to reset replace key battery message Saab 9-3 first generation.
Reset replace key battery message Saab 9-3 first generation. From year: 1998, 1999, 2000, 2001, 2002.
Changing the remote-control battery. When the battery voltage in the remote control falls below a predetermined level the SID will issue the following message: REPLACE KEY BATTERY. Press the CLEAR button on the SID to acknowledge this message. You must then replace the battery without delay to avoid malfunctions. The life of the battery is 4-5 years. After changing the battery you must press the unlocking button of the remote control four times (or until the door locks cycle) while the car is within the range of the remote control in order for the control module to recognize the remote.
Battery for remote control. The battery for the remote control will normally have a life of 4-5 years. When the battery needs changing, ”REPLACE KEY BATTERY” will appear on the SID. After fitting a new battery, press the unlock button on the remote ontrol at least four times in succession, so that the car alarm can recognize the signals from the transmitter. If the remote control has been exposed to very low temperatures, it may not function properly. If this happens, warm it in your hands for a few minutes. If the remote control is not working, it may be because the code signal has not been synchronized with that in the control module for the car alarm. To rectify this, press the unlock button on the remote control at least four times in quick succession. When it is recognized, the door locks will cycle.
Instructions
1. Open the hood and loosen the retaining nut on the cable clamp running to the negative battery terminal.
2. Slide the clamp off of the negative battery terminal.
3. Wait 1 minute for the Range Rover’s electronic control module to cycle and reset. Then, reconnect the clamp to the negative battery terminal.
4. Tighten the retaining nut on the cable clamp. The airbag light should go out at this point. When it does, you’ll know that the fault code has been erased.
2005-2009
Manual Reset Procedure:
Press and hold the trip reset button.
Turn the ignition switch on to the ignition position II (one position before starting engine).
If the SII (Service Indicator Interval) function is enabled the information display will flash ‘SERVICE’ for 5 seconds and then display ‘SERVICE’ constantly. If the SII function is not enabled the information display will show the normal odometer and trip information.
If the trip reset button is released within 10 seconds of entering the reset mode, the information display will show ‘DIST’. If the trip reset button is not released after 10 seconds the instrument cluster will exit the manual reset procedure.
If the oil service value is to be reset, press the trip reset button within 10 seconds for 5 seconds and then reset the oil service value, the display will then show ‘END’.
If the trip reset button is pressed for 5 seconds the display will exit the reset routine. If the trip reset button is not pressed for more than 10 seconds, then the information display will exit the reset routine. Turn the ignition off and then start the engine to verify the indicator has been reset.
How do you reset maintenance light, reset service light indicator Chevrolet Camaro 1999-2010. For reset maintenance light and that can be made manually by use button on car dash board.
Reset service light indicator, engine oil life Chevrolet Camaro, oil reset instructions:
1999-2002
Turn the ignition to run (one position before starting engine).
Press and hold the AVERAGE SPEED and RANGE buttons until the display resets to 100.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2010
Turn the ignition to run (one position before starting engine).
Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds.
If the “Change Engine Oil Soon” message is not on, the system is reset. If it is on, turn the ignition off and repeat steps 1-2.
Turn the ignition off and then start the engine to verify the indicator has been reset.