Tag Archives: push start

Reset oil service light BMW F10

Leave a reply

Reset oil service light BMW F10. From year: 2010, 2011, 2012, 2013.

How to reset oil service light BMW F10.

  1. Switch ignition to ON position, do not start the engine, push start engine/ignition button without depressing clutch/brake.
  2. Wait for the service  warning light to dissapear.
  3. Immediately after service reminder goes out, push & hold only button on bottom left of tacho /instrument display.
  4. Display will change and show brake pad wear indicator picture.
  5. Push and release same button again to scroll through menu.
  6. When you reach the engine oil warning light push & hold the button until option appears to reset interval.
  7. Push and hold, warning light will reset.
  8. Switch OFF the ignition and then on again to see if warning light has been reset.

 

General information. The engine oil consumption is dependent on the driving style and driving conditions. Therefore, check the engine oil level after every refueling using the electronic engine oil level check.

Oil types BMW F10. No oil additives. Oil additives may lead to engine damage. Approved oil types Your service center can advise you on which engine oils have been approved by the manufacturer of your vehicle. The engine oil quality is critical for the life of the
engine. Only use approved BMW High Performance oil. Approved oils belong to the viscosity grades SAE 0W-40, SAE 0W-30, SAE 5W-40 and SAE 5W-30.

Oil service light reset indicator Lexus GX – Series

Leave a reply

Reset service interval display, insp and oil service for Lexus GX-Series, 2004-2010, that can be made manually by use button on car dashboard.

Reset service light indicator, engine oil life Lexus GX-Series, oil reset instructions:

2004-2006
Turn the ignition to run (one position before starting engine).
Bring up the odometer reading using the trip meter reset knob then the turn ignition off.
Hold down the trip meter reset knob while turning the ignition key to the run position (one position before starting engine).
Hold down the knob until the light goes off. Before the light goes off, it illuminates 3 seconds, flashes for 2 seconds and illuminates for 1 second. If the system fails to reset, the light will remain flashing. In this case, return to step 1 and try again.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2007-2009
Turn the ignition to run (one position before starting engine).
Bring up the odometer reading using the trip meter reset knob then the turn ignition off.
Hold down the trip meter reset knob while turning the ignition key to the run position (one position before starting engine).
Keep pressing the knob until the ěMAINT REQDî light goes off. If the light continues flashing, return to step 1 and try again.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2010
Turn the ignition to run – engine off (push START/STOP button once).
Press the Menu switch to change the multi-information display to blank. Turn the engine off.
While pressing the ODO/TRIP button, set the ěENGINE START STOP” switch to run – engine off (push START/STOP button once).
Keep pushing the ěODO/TRIPî switch for more than 7 seconds. While doing this operation, the master warning light comes on, a warning tone sounds and the “RESETTING OIL MAINTENANCE DATA” message appears to inform you that light has been reset. After 5 seconds, the system reset is completed.
Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil service light reset indicator Lexus GS – Series

Leave a reply

Reset service interval display, insp and oil service for Lexus GS – Series, 2006-2010 that can be made manually by use button on car dashboard.

Reset service light indicator, engine oil life Lexus GS – Series, oil reset instructions:

2006
Turn the ignition to run (one position before starting engine).
Push the ěODO TRIPî switch to change the display to blank. Turn the ignition off.
While pressing the trip meter reset button, set the engine switch to run (one position before starting engine).
Keep pushing the ěRESETî switch for more than 7 seconds. While doing this operation, the master warning light comes on, a warning tone sounds and the “OIL MAINT RESET” message appears to inform you that light has been reset.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2007
Turn the ignition to run (one position before starting engine).
Press the ěDISPî switch to change the multi-information display to blank. Turn the ignition off.
While pressing the trip meter reset button, set the engine switch to run (one position before starting engine).
Keep pushing the ěRESETî switch for more than 7 seconds. While doing this operation, the master warning light comes on, a warning tone sounds and the “OIL MILEAGE RESET” message appears to inform you that light has been reset. After 5 seconds, the system reset is completed.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2008-2010
Turn the ignition to run – engine off (push START/STOP button once).
Press the ěDISPî switch to change the multi-information display to blank. Turn the ignition off.
While pressing the trip meter reset button, set the engine switch to run – engine off (push START/STOP button once).
Keep pushing the ěRESETî switch for more than 7 seconds. While doing this operation, the master warning light comes on, a warning tone sounds and the “OIL MESSAGE RESET” message appears to inform you that light has been reset. After 5 seconds, the system reset is completed.
Turn the ignition off and then start the engine to verify the indicator has been reset.