Tag Archives: phone

Reset tire pressure warning light Toyota Rav4 XA40

Reset tire pressure warning light Toyota Rav4 XA40 fourth generation. From year: 2013, 2014.

How to reset oil service light Toyota Rav4, 3 generation XA30, 4 generation.

How to initialize the tire pressure warning system.

  1. Park the vehicle in a safe place and turn the engine switch to the “LOCK” position (vehicles without a smart key system) or off (vehicles with a smart key system). Initialization cannot be performed while the vehicle is moving.
  2. Adjust the tire inflation pressure to the specified cold tire inflation pressure level. Make sure to adjust the tire pressure to the specified cold tire inflation pressure level. The tire pressure warning system will operate based on this pressure level.
  3. Turn the engine switch to the “ON” position (vehicles without a smart key system) or IGNITION ON mode (vehicles with a smart key system).
  4. Press and hold the tire pressure warning reset switch until the tire pressure warning light blinks slowly 3 times.
  5. Reset-tire-pressure-warning-light-Toyota-Rav4-XA40
  6. Vehicles without a smart key system: Wait for a few minutes with the engine switch in the “ON” position and then turn the engine switch to the “ACC” or “LOCK” position. Vehicles with a smart key system: Wait for a few minutes with the engine switch in IGNITION ON mode and then turn the engine switch off.

Registering ID codes Toyota Rav 4.

The tire pressure warning valve and transmitter is equipped with a unique ID code. When replacing a tire pressure warning valve and transmitter, it is necessary to register the ID code. Have the ID code registered by your Toyota dealer.

When to replace your vehicle’s tires. Tires should be replaced if:

  • You have tire damage such as cuts, splits, cracks deep enough to expose the fabric, and bulges indicating internal damage.
  • A tire goes flat repeatedly or cannot be properly repaired due to the size or location of a cut or other damage.

If you are not sure, consult with your Toyota dealer.

Replacing tires and wheels (vehicles with the tire pressure warning system).

If the ID code of the tire pressure warning valve and transmitter is not registered, the tire pressure warning system will not work properly. After driving for about 20 minutes, the tire pressure warning light blinks for 1 minute and stays on to indicate a system malfunction.

Tire life Toyota Rav4.

Any tire over 6 years old must be checked by a qualified technician even if it has seldom or never been used or damage is not obvious.

Routine tire inflation pressure checks (vehicles with the tire pressure warning system).

The tire pressure warning system does not replace routine tire inflation pressure checks. Make sure to check tire inflation pressure as part of your routine of daily vehicle checks.

Situations in which the tire pressure warning system may not operate properly (if equipped).

In the following cases, the tire pressure warning system may not operate properly.

  • If non-genuine Toyota wheels are used.
  • A tire has been replaced with a tire that is not an OE (Original Equipment) tire.
  • A tire has been replaced with a tire that is not of the specified size.
  • Tire chains etc. are equipped.
  • Lock nuts are equipped.
  • An auxiliary-supported run-flat tire is equipped.
  • If a window tint that affects the radio wave signals is installed.
  • If there is a lot of snow or ice on the vehicle, particularly around the wheels or wheel housings.
  • If the tire inflation pressure is extremely higher than the specified level.
  • If the spare tire is in a location subject to poor radio wave signal reception.
  • If a large metallic object which can interfere with signal reception is put in

*: Vehicles with a full-size spare tire only

Performance may be affected in the following situations.

  • Near a TV tower, electric power plant, gas station, radio station, large display, airport or other facility that generates strong radio waves or electrical noise.
  • When carrying a portable radio, cellular phone, cordless phone or other wireless communication device.

When the vehicle is parked, the time taken for the warning to start or go off could be extended.
When tire inflation pressure declines rapidly for example when a tire has burst, the warning may not function.

Oil service reset Mercedes Benz SLS – Class

Reset service light indicator, engine oil life Mercedes Benz SLS – Class, year: 2010-2012, oil reset instructions:

1. Turn the ignition to position 1. (close all doors
2. Press the system selection button (left button on left steering wheel controls) repeatedly until the kilometer reading is shown in the multi information display.)
3. Press the system selection button (located on the far left of the steering wheel) repeatedly until the menu item “”trip”” with highlighter is stored in the multi-function display. *Trip remains selected for 5 seconds so you need to move to step 4.”
4. First press and hold the accept phone call button and within 1 second also press and hold the OK button for 5 seconds. The workshop menu will appear in the display showing “”vehicle data
5. Press the scroll forward button (lower button on left steering wheel controls) to highlight “”ASSYST PLUS”” and then confirm by pressing OK button.”
6. Press scroll forward button (lower button on left steering wheel controls) to highlight “”Full Service”” and then confirm by pressing OK button.”
7. Press scroll forward button until “”YES”” is highlighted and confirm swith OK button. “”No take-back possible”” appears.”
8. Press scroll forward button until “”Confirmation”” is highlighted and confirm with OK button. “”Full service carried out”” appears.”
9. Press OK button and back button (standalone button on left steering wheel controls) repeatedly until the menus are exited.
10. Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil service reset Mercedes Benz GLK – Class

Reset service light indicator, engine oil life Mercedes Benz GLK – Class, year: 2009-2011, oil reset instructions:

1. Turn the ignition to position 1. Ensure mileage is displayed.
2. Press the left arrow repeatedly until the TRIP option is highlighted.
3. Press and hold (phone) button and within 1 second press OK and then hold both buttons for 5 seconds. The shop menu is displayed.
4. Press down repeatedly until “”ASSYST PLUS”” is highlighted and confirm with OK. ”
5. Use the down arrow to select “”FULL SERVICE”” and then confirm with OK. Use the down arrow to select YES and confirm with OK. “”CANNOT BE UNDONE”” displays. Use the down arrow to select CONFIRM and then confirm with OK. The display reads “”FULL SERVICE CARRIED OUT””. Confirm by pressing OK.”
6. Turn the ignition off and then start the engine to verify the indicator has been reset.