Tag Archives: odometer reading

How reset trip odometer display indicates Fiat 500

Leave a reply

Fiat 500 odometer / trip odometer / electronic vehicle information center (EVIC) display area.

Reset trip odometer Fiat 500. From year: 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014.

This display indicates the total distance the vehicle has been driven. U.S. Federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven. If your odometer needs to be repaired or serviced, the repair technician should leave the odometer reading the same as it was before the repair or service. If s/he cannot do so, then the odometer must be set at zero, and a sticker must be placed in the door jamb stating what the mileage was before the repair or service. It is a good idea for you to make a record of the odometer reading before the repair/ service, so that you can be sure that it is properly reset, or that the door jamb sticker is accurate if the odometer must be reset at zero.

If the vehicle is equipped with the Electronic Vehicle Information Center (EVIC) in the instrument cluster, all warnings including “door” and “gate” and “Change Engine Oil” will only be displayed in the EVIC display. For additional information, refer to “Electronic Vehicle Information Center (EVIC).” Refer to the “Electronic Vehicle Information Center (EVIC)” for further information.

ELECTRONIC VEHICLE INFORMATION CENTER (EVIC).

The Electronic Vehicle Information Center (EVIC) features a driver-interactive display that is located in the instrument cluster.

Reset front passenger’s seat belt reminder light Toyota FJ Cruiser

Leave a reply

How to reset front passenger’s seat belt reminder light Toyota FJ Cruiser.
Reset front passenger’s seat belt reminder light Toyota FJ Cruiser. From year: 2007, 2008, 2009, 2010, 2011.

The light and buzzer act as a reminder to have the front passenger buckle up the seat belt. Once the ignition key is turned to “ON” or “START”, the reminder light flashes if a passenger sits in the front passenger seat and does not fasten the seat belt. If the vehicle speed rises above 20 km/h (12 mph) with the seat belt unfastened, the buzzer will sound for 10 seconds. Then, if the seat belt is still unfastened, the buzzer will sound in a different tone for 20 seconds. Even if the vehicle speed drops below 20 km/h (12 mph), the buzzer will continue to sound. To stop the buzzer, fasten the seat belt. If the buzzer still sounds, make sure the driver’s seat belt is fastened. If luggage or other load is placed on the front passenger seat, depending on its weight, the reminder light may flash and buzzer to sound.

The buzzer can be set not to sound by following the procedure below.

  1. Sit on the front passenger seat.
  2. Turn the ignition key to the “OFF” position with the odometer reading shown. For details see the Odometer and two trip meters om Toyota categories.
  3. Turn the ignition key to the “ON” position.
  4. Within 6 seconds, push the trip meter reset knob and hold it for more than 10 seconds.
  5. Insert the tab of front passenger seat belt into the buckle.
  6. The odometer shows either “b−on” or “b−off”. The reading changes by pushing the trip meter reset knob and the setting of the front passenger seat belt reminder buzzer can be changed. The odometer display returns to normal if the meter reset knob has not been operated for more than 10 seconds or the ignition key is turned to the “OFF” position.

All information how can you reset front passenger’s seat belt reminder light is taken from Toyota FJ Cruiser owners manual.

Reset oil service light indicator Toyota Tundra second generation

Leave a reply

Reset oil service light indicator, engine oil life Toyota Tundra 2. From year: 2005-2014 reset instructions:

How to reset oil service light Toyota Tundra 2 generation.

This light acts as a reminder when to replace the engine oil. This light will come on when the ignition key is turned to “ON” and will go off after about a few seconds. When you drive for about 7200 km (4500 miles) after the engine oil replacement, this light illuminates for about 3 seconds and then flashes for about 12 seconds with the ignition key turned to the “ON” position. If you continue driving without replacing the engine oil, and if the distance driven exceeds 8000 km (5000 miles), the light will come on after the ignition key is turned to “ON” position. The light will remain on thereafter. If the light is flashing, we recommend that you replace the engine oil at an early opportunity depending on the driving and road conditions. If the light comes on, replace it as soon as possible.

The system must be reset after the engine oil replacement. Reset the system by the following procedure:

When tje Maint Requd appears on a Toyota Tundra you must follow this steps to reset the warning light.

1. Turn the ignition key to the “ACC” or “LOCK” position with the odometer reading shown.
2. Turn the ignition key to the “ON” position while holding down the trip meter reset knob. See below pictures.
3. On dash will appear ” – – – – – – ” who will blink.
4. Hold down the knob for at least 5 seconds. The odometer indicates “000000” and the light goes off.
5. If the system fails to reset, the light will continue flashing.

All information how can you reset oil service light is taken from Toyota Tundra second generation owners manual.

Reset oil service light Toyota Tacoma second generation

Leave a reply

Reset oil service light Toyota Tacoma second generation. From year: 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014.

How to reset maint reqd service light Toyota Tacoma 2 generation.

Reset-oil-service-light-Toyota-Tacoma-second-generation.

Engine Oil Replacement Reminder Light (for vehicles sold in U.S.A.).

This light acts as a reminder to replace the engine oil. This light will come on when the ignition key is turned to “ON” and will go off after about a few seconds. When you drive for about 7200 km (4500 miles) after the engine oil replacement, this light illuminates for about 3 seconds and then flashes for about 12 seconds with the ignition key turned to the “ON” position. If you continue driving without replacing the engine oil, and if the distance driven exceeds 8000 km (5000 miles), the light will come on after the ignition key is turned to “ON” position. The light will remain on thereafter.

If the light is flashing, we recommend that you replace the engine oil at an early opportunity depending on the driving and road conditions. If the light comes on, replace it as soon as possible. The system must be reset after the engine oil replacement. Reset the system by the following procedure:

  1. Turn the ignition key to the “OFF” position with the odometer reading shown. For details, see “Odometer and two trip meters” in this category.
  2. Turn the ignition key to the “ON” position while holding down the trip meter reset knob. See below picture.
  3. How-to-reset-maint-reqd-service-light-Toyota-Tacoma-2-generation.
  4. Hold down the knob for at least 5 seconds. The odometer indicates “000000” and the light goes off.

If the system fails to reset, the light will continue flashing.

All information how can you reset oil service light is taken from Toyota Tacoma second generation owners manual.

 

That it is the full procedure how to reset oil service light Toyota Tacoma second generation. If you like to reset any maintenance oil light after an oil change. Or reset check engine light, airbag light, inspection key or insp errors when maint reqd, for Toyota cars. Or any warning light for service reminder which appears on the display. Write in the search box the car name for which you want to find information, and find how to reset other service reminders by yourself.

This is an information site where you can solve your car problems. Send us a comment if our procedures are correctly. If you would have anything to add, for us every opinion counts.

Reset service light, maintance on Toyota Land Cruiser

Leave a reply

1. Turn your ignition key to the ‘ACC’ or ‘LOCK’ position.
2. Press and hold the trip meter reset nob (next to your Toyota Land Cruiser’s odometer).
3. While holding the trip meter reset nob, turn the ignition to ‘ON’, but do not start your Toyota Land Cruiser.
4. Hold the meter reset until the MAINT REQD light switches off.

If this procedure does not successfully reset your maintenance required light, make sure that your digital odometer is set with the odometer reading showing and try again. If the light is still lit, you can try disconnecting your Toyota Land Cruiser battery, causing the internal computer to reset. If you still haven’t successfully turned off the oil indicator MAINT REQD light, please read your manual or contact your dealer for further instruction!