Tag Archives: odometer

Reset odometer and two trip meters Toyota Land Cruiser 100 series

Leave a reply

How to reset odometer and two trip meters Toyota Land Cruiser 100 series.

Reset odometer and two trip meters Toyota Land Cruiser 100 series. From year: 2002, 2003, 2004, 2005, 2006, 2007.

Reset-odometer-and-two-trip-meters-Toyota-Land-Cruiser-100-series

 

 

 

 

 

 

 

This meter displays the odometer and two trip meters.

  1. Odometer-Shows the total distance the vehicle has been driven.
  2. Two trip meters-Show two different distances independently driven since the last time each trip meter was set to zero. You can use one trip meter to calculate the fuel economy and the other to measure the distance on each trip. All trip meter data is cancelled if the electrical power source is disconnected.
  3. Trip meter reset knob-Resets the two trip meters to zero, and also change the meter display. To change the meter display, quickly push and release the knob. The meter display changes in the order from the odometer to trip meter A to trip meter B, then back to the odometer each time you push. To reset the trip meter A to zero, display the meter A reading, then push and hold the knob until the meter is set to zero. The same process can be applied for resetting the trip meter B.

All information how to reset odometer and two trip meters is taken from Toyota Land Cruiser 100 series owners manual.

Reset odometer and two trip meters Toyota Tacoma 2 generation

Leave a reply

Reset odometer and two trip meters Toyota Tacoma 2 generation. From year: 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014.

How to reset odometer and two trip meters Toyota Tacoma second generation.

Reset-odometer-and-two-trip-meters-Toyota-Tacoma-2-generation.

This meter displays the odometer and two trip meters.

  1. Odometer-Shows the total distance the vehicle has been driven.
  2. Two trip meters-Show two different distances independently driven since the last time each trip meter was set to zero. You can use one trip meter to calculate the fuel economy and the other to measure the distance on each trip. All trip meter data is cancelled if the electrical power source is disconnected.
  3. Trip meter reset knob-Resets the two trip meters to zero, and also change the meter display. To change the meter display, quickly push and release the knob. The meter display changes in the order from the odometer to trip meter A to trip meter B, then back to the odometer each time you push. To reset the trip meter A to zero, display the meter A reading, then push and hold the knob until the meter is set to zero. The same process can be applied for resetting the trip meter B.

All information how to reset odometer and two trip meters is taken from Toyota Tacoma 2 generation owners manual.

That it is the full procedure how to reset odometer and two trip meters Toyota Tacoma 2 generation. If you like to reset any maintenance oil light after an oil change. Or reset check engine light, airbag light, inspection key or insp errors when maint reqd, for Toyota cars. Or any warning light for service reminder which appears on the display. Write in the search box the car name for which you want to find information, and find how to reset other service reminders by yourself.

This is an information site where you can solve your car problems. Send us a comment if our procedures are correctly. If you would have anything to add, for us every opinion counts.

Reset oil service light Toyota Rav4 XA30

Leave a reply

Reset oil service light Toyota Rav4, third generation XA30. From year: 2009, 2010, 2011, 2012, 2013.

How to reset oil service light Toyota Rav4, 3 generation XA30.
To reset the oil change system, follow the procedure below:
Vehicles without smart key system.
  1. Turn the engine switch off with the trip meter A reading shown.
  2. While pressing the trip meter reset button, turn the engine switch to the “ON” position.
  3. Press and hold the button until the trip meter displays “000000”.

 

Vehicles with smart key system.
  1. Turn the “ENGINE START STOP” switch off with the trip meter A reading shown.
  2. While pressing the trip meter reset button, turn the “ENGINE START STOP” switch to IGNITION ON mode.
  3. Press and hold the button until the trip meter displays “000000”.
All information how to reset oil service light is taken from Toyota Rav 4 owners manual.
Used engine oil. Used engine oil contains potentially harmful contaminants which may cause skin disorders such as inflammation or skin cancer, so care should be taken to avoid prolonged and repeated contact. To remove used engine oil from your skin, wash thoroughly with soap and water.
Dispose of used oil and filters only in a safe and acceptable manner. Do not dispose of used oil and filters in household trash, in sewers or onto the ground. Call your Toyota dealer, service station or auto parts store for information concerning recycling or disposal.
Do not leave used engine oil within the reach of children.
 Reset-oil-service-light-Toyota-Rav4-XA30
.
Vehicles without smart key system.
  • The following gauges, meters and displays illuminate when the engine switch is in the “ON” position.
Vehicles with smart key system.
  • The following gauges, meters and displays illuminate when the “ENGINE START STOP” switch is in IGNITION ON mode.
  • Tachometer. Displays the engine speed in revolutions per minute.
  • Speedometer. Displays the vehicle speed.
  • Engine coolant temperature gauge. Displays the engine coolant temperature.
  • Fuel gauge. Displays the quantity of fuel remaining in the tank.
  • Trip information display.
  • Automatic transmission shift position indicator lights.
  • Odometer/trip meter.
  • Odometer. Displays the total distance the vehicle has been driven.
  • Trip meter. Displays the distance the vehicle has been driven since the meter was last reset. Trip meters A and B can be used to record and display different distances independently.
  • Odometer/trip meter switching and trip meter resetting button. Switches between odometer and trip meter displays. Pushing and holding the button will reset the trip meter when the trip meter is being displayed.

Oil Service Reset BMW Z8

Leave a reply

Reset service light indicator, engine oil life BMW Z8 year 2000-2003 reset instructions:

BMW recommends the use of a reset tool.

Manual Reset

1. Turn off the ignition.
2. Press and hold the TRIP ODOMETER button in the instrument cluster and turn the ignition to Accessory.
3. Keep the button pressed for 5 seconds until OIL SERVICE RESET (RE) or INSPECTION RESET (RE) appears in the display. Then release the button.
4. Press and hold the button again for 5 seconds until RE or RESET flashes in the display. Then release the button.
5. With the display flashing
6. Turn the ignition off and start the engine to verify the indicator has been reset.

Service Light Reset SCION xB

Leave a reply

2004-2011

1. Turn the ignition to run (one position before starting engine).
2. Select trip metre A reading by using the trip metre button and then turn the ignition off.
3. While pressing the trip meter reset button
4. Continue to press and hold the button until the trip meter displays “”000000″”.”
5. Turn the ignition off and then start the engine to verify the indicator has been reset.

2012

1. Turn the ignition to run (one position before starting engine).
2. Select trip metre A reading by using the trip metre button and then turn the ignition off.
3. While pressing the trip button for 5 seconds
4. The reset is complete when the MAINT REQ light turn off and the odometer indicates 0 and then returns to its regular display.
5. Turn the ignition off and then start the engine to verify the indicator has been reset.