Tag Archives: models

Reset service light Toyota Sequoia first generation

Leave a reply

Reset VSC trac warning light Toyota Sequoia first generation. From year: 2005, 2006, 2007.

How to reset VSC trac warning light Toyota Sequoia 1 generation.

This light warns that there is a problem somewhere in the vehicle stability control system and traction control system (two−wheel drive models) or active traction control system (four−wheel drive models). The light will come on when the ignition key is turned to “ON” and will go off after a few seconds. If the light comes on while driving, the system does not work. However, as conventional braking operates when applied, there is no problem to continue your driving.

In the following cases, contact your Toyota dealer:

  • The warning light does not come on after the ignition key is turned to “ON”.
  • The warning light remains on after the ignition key is turned to “ON”.
  • The warning light comes on while driving.

    • All information how can you reset VSC trac warning light is taken from Toyota Sequoia owners manual.

    Reset service light Toyota Sequoia first generation

    Leave a reply

    Reset VSC trac warning light Toyota Sequoia first generation. From year: 2005, 2006, 2007.

    How to reset VSC trac warning light Toyota Sequoia 1 generation.

    This light warns that there is a problem somewhere in the vehicle stability control system and traction control system (two−wheel drive models) or active traction control system (four−wheel drive models). The light will come on when the ignition key is turned to “ON” and will go off after a few seconds. If the light comes on while driving, the system does not work. However, as conventional braking operates when applied, there is no problem to continue your driving.

    In the following cases, contact your Toyota dealer:

  • The warning light does not come on after the ignition key is turned to “ON”.
  • The warning light remains on after the ignition key is turned to “ON”.
  • The warning light comes on while driving.

    • All information how can you reset VSC trac warning light is taken from Toyota Sequoia owners manual.

    Oil service light reset indicator Volvo 850-70

    Leave a reply

    Reset service interval display, insp and oil service for Volvo 850-70, that can be made manually by use button on car dashboard.

    Reset service light indicator, engine oil life Volvo 850-70, oil reset instructions:

    RESETTING 5000 MILE SERVICE LAMP ON 1994 + 1995 850

    NOTE: This function is for the service reminder lamp, be sure you have performed the proper service such as changing the oil before resetting. If the check engine lamp is illuminated when the car is running, you’ll need to have the car looked at by the Volvo dealer for proper diagnosis.

    1. Turn on the ignition to the KPII position so the warning lamps on the dash are illuminated. Do not start the car.

    2. Open the bonnet of the car and locate Diagnostic test port (A) behind the driver side headlamp.

    3. Remove the cover and pull the jumper wire out of the holder in the cover.

    4. Insert the jumper into terminal #7, then press button 4 times, wait approximately 5 seconds and the red lamp should glow continuously. You are now in the data reset mode.

    5. Press the button 1 time and wait approximately 5 seconds for the lamp to glow again then press the button 5 times. After about 5 seconds the lamp will illuminate again, press the button 1 time and you will see the lamp flash repeatedly for a couple of seconds indicating that the service lamp has been properly reset.

    6. If a mistake is made, simply switch the ignition off and back on to reset and start over.

    1996 Model (Some of them)
    On these models the diagnostic socket is in front of the gear stick. Switch the ignition on. As you look at the speedometer on the dash, beneath it opposite the trip reset button is a rubber plug. Remove the plug and with a thin pointer such as a ball point pen, depress the pin. This will reset the service light.

    1999 Model Service Lamp Reset Procedure

    1. Press and hold trip odometer reset button

    2. Turn ignition key to run position KPII (not the start position)

    3. Wait 30 seconds or until service light begins blinking

    4. Release Trip Odometer button

    5. Turn ignition to off position

    Oil service reset Volkswagen Jetta

    Leave a reply

    Reset service light indicator, engine oil life Volkswagen Jetta, year 1993-2010 reset instructions:

    Turn the ignition to run (one position before starting engine).
    Press and hold the button located under the speedometer.
    Switch ignition off and release button. Message OIL appears in the display.
    Press MINUTE button of digital clock or button for setting analog clock only as long as 5 dashes appears in display.
    Turn the ignition off and then start the engine to verify the indicator has been reset.

    2000-2004

    Reset may be similar to previous year or other models – Oil Reset will verify and update site.

    2005-2010

    Manual Reset:
    Turn the ignition to run (one position before starting engine).
    Press and HOLD the trip-odometer button “0.0”.
    Turn your key to run (one position before starting engine).
    Release the trip-odometer button.
    Push and release the Clock Minute Set Button “min”.
    Turn the ignition off and then start the engine to verify the indicator has been reset.

    Reset service light oil life indicator Honda Insight

    Leave a reply

    Reset service light indicator, engine oil life Honda Insight, year 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010 reset instructions:

    2000-2005
    Turn off the engine.
    Press and hold the TRIP button in the instrument panel and turn the ignition switch to run (one position before starting).
    Hold the button for at least 10 seconds, until the “MAINT REQD” indicator goes out.
    Turn the ignition off and then start the engine to verify the indicator has been reset.

    2006
    Turn off the engine.
    Press and hold the SELECT/RESET button in the instrument panel and turn the ignition switch to run (one position before starting).
    Hold the button for at least 10 seconds, until the indicator resets.
    Turn the ignition off and then start the engine to verify the indicator has been reset.

    2010
    Turn the ignition to run (one position before starting engine).
    If the engine oil life is not displayed, press the SEL/RESET button on the steering wheel repeatedly until it is.
    Press and hold the SEL/RESET button for more than 10 seconds. The remaining engine oil life reset mode will be shown on the multi information display.
    Select RESET by pressing the INFO (▲/▼) button, then press the SEL/RESET button to reset the engine oil life display. The maintenance item code(s) will disappear, and the engine oil life will reset to 100.
    Turn the ignition off and then start the engine to verify the indicator has been reset.

    *Models equipped with the keyless access system have an engine start/stop button instead of an switch. ON Mode is equivalent of ignition (II).