Tag Archives: light

Servive light reset oil life indicator dashboard Dodge Challenger

Leave a reply

How do you reset maintenance light, reset service light indicator Dodge Challenger, year 2013, 2014, 2015. For reset maintenance light and that can be made manually by use button on car dash board.

Reset service light indicator, engine oil life Dodge Challenger, year 2013, 2014, 2015 oil reset instructions:

  1. Turn the ignition to run (one position before starting engine).
  2. Fully depress the accelerator pedal slowly three times within 10 seconds.
  3. Turn the ignition off and then start the engine to verify the indicator has been reset.

or

  1. Turn the ignition to run (one position before starting engine).
  2. Push and release the DOWN arrow button to scroll downward through the main menu to “ Vehicle Info.”
  3. Push and release the RIGHT arrow button to access the ”Oil Life” screen.
  4. Push and hold the OK button until the “ Oil Life” screen displays.
  5. Push and release the DOWN arrow button to select “ Yes,” then push and release the OK button to select reset of the Oil Life.
  6. Push and release the Up arrow button to exit the submenu screen.
  7. Turn the ignition off and then start the vehicle to verify the indicator has been reset.

Reset service spanner light Fiat Ducato

Leave a reply

How to reset service wrench light on a Fiat Ducato second edition.

Reset service spanner light Fiat Ducato. From year : 2002, 2003, 2004, 2005, 2006, 2007.

  • Turn ignition to on without starting the engine.
  • Press and hold the button situated in right side of the dashboard.
  • The button must be held down for about 10 seconds until the display shows a spanner and CFG 1.
  • Release the button and then press it again and hold down for about 5 seconds until the CFG1 and wrench key will disappear.
  • Done, you managed to resetservice spanner light Fiat Ducato 2.

Oil reset service light indicator MINI Paceman

Leave a reply

How do you reset maintenance light, reset service light indicator MINI Paceman, year 2013, 2014. For reset maintenance light and that can be made manually by use button on car dash board.

Reset service light indicator, engine oil life MINI Paceman, oil reset instructions:

2013-2014

  1. Turn ignition to Terminal 15 which is one turn of the key or one press of the START/STOP button.
  2. Press and hold the trip odometer reset button for approximately 10 seconds until the first service job appears in the display.
  3. The upper display in the Instrument Cluster will be illuminated with a Service Item (example: An oil can is the designation for Oil Service). The lower display in the Instrument Cluster will indicate the remaining time or mileage left for that Service Item (example: 14000). Press the on-board computer button repeatedly (located on the direction indicator/main-beam switch) to scroll through all of the Condition Based Service Items.
  4. Press and hold the on-board computer button on the direction indicator/main-beam switch until “RESET” appears in the lower display.
  5. Pressing the on-board computer button again resets the service shown in the upper display. Repeat the procedure for each additional service which is to be reset.
  6. Turn the ignition off and start the engine to verify the indicator has been reset.

Reset light airbag fault code Range Rover

Leave a reply

How to reset airbag fault code Range Rover.

Reset airbag fault code Range Rover. How to reset the Range Rover Airbag Fault Code warning light. Reset AIRBAG FAULT error message on dash board on a Range Rover.

Instructions:

  1. Open the hood and loosen the retaining nut on the cable clamp running to the negative battery terminal.
  2. Slide the clamp off of the negative battery terminal.
  3. Wait 1 minute for the Range Rover’s electronic control module to cycle and reset. Then, reconnect the clamp to the negative battery terminal.
  4. Tighten the retaining nut on the cable clamp. The airbag light should go out at this point. When it does, you’ll know that the fault code has been erased.

Reset tire pressure warning light Toyota Solara 2 generation

Leave a reply

Reset tire pressure warning light Toyota Solara 2 generation. From year: 2004, 2005, 2006, 2007, 2008.

How to reset tire pressure warning light Toyota Solara second generation.

Reset-tire-pressure-warning-light-Toyota-Solara-2-generation

This light warns that the tire pressure of one or more of your tires (including ground spare tire) is low. The light comes on when the ignition key is turned to the “ON” position. It goes off after a few seconds. This indicates that the tire pressure warning system is functioning properly. If the warning light comes on, stop your vehicle in a safe place as soon as possible and check that the inflation pressure of all tires (including ground spare tire) is as specified on the tire and loading information label.

The light should go off a few minutes after the tire pressure is adjusted.

If the warning light comes on after blinking for 1 minute, the tire pressure warning system may be malfunctioning. Contact your Toyota dealer.

TIRE PRESSURE WARNING RESET SWITCH.

When initializing the system, the present tire inflation pressure is stored as standard. The tire pressure warning system determines decreased air pressure by comparing the present and the standard tire inflation pressures. When you change the set tire inflation pressure, it is necessary to initialize the tire pressure warning system.

  • When changing the tire size.
  • When rotating the tire on vehicles differing with front and rear tire inflation pressure.

To initialize the system, perform the following:

  1. Park the vehicle in a safe place and turn the ignition key to “OFF” position.
  2. Adjust the pressure of all the installed tires to the specified cold tire inflation pressure level.
  3. Turn the ignition key to the “ON” position.
  4. Push and hold the tire pressure warning reset switch until the tire pressure warning light blinks slowly three times.
  5. Leave for a few minutes with the ignition key in “ON” position, and then turn the ignition key to “OFF” position.

If you push the tire pressure reset switch while vehicle is moving, initialization is not performed. If you push the tire pressure reset switch accidentally and initialization is performed, adjust the tire inflation pressure to the specified level and initialize the system again.

If the tire pressure warning light does not blink slowly three times when you push and hold the reset switch, initialization has failed and the tire pressure warning system may not work properly. In this case, initialize the system again. If initialization cannot be performed, have the system checked at your Toyota dealer.

Do not push the reset switch without first adjusting the tire inflation pressure to the specified level. Otherwise, the tire pressure warning light may not come on even if the tire inflation pressure is low, or it may come on when the tire inflation pressure is actually normal.

That it is the full procedure how to reset tire pressure warning light Toyota Solara second generation. If you like to reset any maintenance oil light after an oil change. Or reset check engine light, airbag light, inspection key or insp errors when maint reqd, for Toyota cars. Or any warning light for service reminder which appears on the display. Write in the search box the car name for which you want to find information, and find how to reset other service reminders by yourself.