Tag Archives: left hand side

Reset oil service light Subaru Impreza 2013

Leave a reply

How to reset oil service light Subaru Impreza 2013.

Reset service light indicator, engine oil life Subaru Impreza, year 2013 reset instructions:

1. Turn the ignition to run (one position before starting engine).
2. Using the controsl on the left hand side of the steering wheel. Pull the i/Set button towards you to bring up the selection screen.
3. Use the Up or Down arrow to highlight the MAINTENANCE menu and pull the i/Set switch towards you.
4. Select the maintenance item (i.e. Engine Oil, Oil Filter) and pull the i/SET switch towards you.
5. Change the next service date and interval with the Up and Down arrow and confirm by highlighting SET and pull the i/SET switch towards you. The reset is complete when the screen shows Setting Complete.
6. Turn the ignition off and then start the engine to verify the indicator has been reset.
*Reset only available on models with the multi-information display

Reset oil service light Subaru Impreza 2012

Leave a reply

How to reset oil service light Subaru Impreza 2012.

Reset service light indicator, engine oil life Subaru Impreza, year 2012 reset instructions:

1. Turn the ignition to run (one position before starting engine).
2. Using the controsl on the left hand side of the steering wheel. Pull the i/Set button towards you to bring up the selection screen.
3. Use the Up or Down arrow to highlight the MAINTENANCE menu and pull the i/Set switch towards you.
4. Select the maintenance item (i.e. Engine Oil, Oil Filter) and pull the i/SET switch towards you.
5. Change the next service date and interval with the Up and Down arrow and confirm by highlighting SET and pull the i/SET switch towards you. The reset is complete when the screen shows Setting Complete.
6. Turn the ignition off and then start the engine to verify the indicator has been reset.

Reset oil service light Subaru Forester

Leave a reply

How to reset oil service light Subaru Forester 2014.

Reset service light indicator, engine oil life Subaru Forester, year 2014 reset instructions:

  1. Turn the ignition to run (one position before starting engine).
  2. Using the controsl on the left hand side of the steering wheel. Pull the i/Set button towards you to bring up the selection screen.
  3. Use the Up or Down arrow to highlight the MAINTENANCE menu and pull the i/Set switch towards you.
  4. Select the maintenance item (i.e. Engine Oil, Oil Filter) and pull the i/SET switch towards you.
  5. Change the next service date and interval with the Up and Down arrow and confirm by highlighting SET and pull the i/SET switch towards you. The reset is complete when the screen shows Setting Complete.
  6. Turn the ignition off and then start the engine to verify the indicator has been reset.

 

Reset the service oil light on Jaguar S-type

Leave a reply

How do you reset maintenance light, reset service light indicator Jaguar S-type. For reset maintenance light and that can be made manually by use button on car dash board.

Reset service light indicator, engine oil life Jaguar S-type, oil reset instructions:

Here’s how to do it yourself in no time works on a few different Jags….

Service Light Reset Instructions:

1 . Insert key into ignition.
2 . Press and hold the Reset switch (located on the Trip Computer Switchpack ).
3 . NOTE: The reset switch has to be released immediately after the ignition is switched ‘ON’. This is critical to enable the rest of the procedure.
Turn the key to Ignition position II and at the point of entering Ignition position II (i.e when a click is heard), instantaneously release the Reset switch.
4 . Wait one second.
5 . Press and hold the Trip switch (located on the end of the left-hand side stalk).
6 . Wait one second.
7 . Press and hold the Reset switch (whilst still holding the Trip switch).
8 . The cluster should display (within three seconds) the warning message ‘RESETTING SERVICE MODE’.
9 . Keep both buttons pressed until the warning message changes to ‘SERVICE MODE RESET’ (after ten seconds).
10 . Once the message is displayed the buttons may be released — sequence is now complete.
11 . If a Service Required message was displayed prior to the reset sequence, cycle the ignition to ‘Off’ and then back to Ignition position II and check that the message is no longer displayed.

Service oil reset Mercedes Benz G Class

Leave a reply

Reset service light indicator, engine oil life Mercedes Benz G – Class, year: 2002, oil reset instructions:

Turn key in steering lock to position 2.
Press either of the lower two system select buttons on left hand side of steering wheel (looks like 2 over lapping file folders) until the trip and main odometer display appears.
Press either of the top buttons on steering wheel (arrows) until the FSS indicator appears.
Press R button on the instrument cluster for 2-4 seconds.
The display reads “DO YOU WANT TO RESET SERVICE INTERVAL? CONFIRM BY PRESSING R”.
Press R button on the instrument cluster again and hold until signal sounds (about 10 seconds). Message now reads “SERVICE INTERVAL HAS BEEN RESET”.
2003
Turn on the ignition (standard display of the control system appears).
Press button (UP arrow) or (DOWN arrow) on the multifunction steering wheel until the FSS indicator appears in the multifunction display.
Press the reset knob for about 4 seconds. The message appears in the tachometer “DO YOU WANT TO RESET SERVICE INTERVAL? CONFIRM BY PRESSING R”.
To confirm, hold down the reset knob until you hear a signal. The service indicator now displays the reset interval.
2004
Turn on the ignition (standard display of the control system appears).
Press button (UP arrow) or (DOWN arrow) on the multifunction steering wheel until the FSS indicator appears in the multifunction display.
Press the reset knob for about 3 seconds. The message appears in the tachometer “SERVICE INTERVAL? RESET WITH R BUTTON FOR 3 SEC.”.
To confirm, hold down the reset knob until you hear a signal. The service indicator now displays the reset interval.