Tag Archives: key system

Reset oil maintenance required Toyota Venza

Leave a reply

How do you reset maintenance light, reset service light indicator Toyota Venza, From year: 2008, 2009, 2010, 2011, 2012, 2013. For reset maintenance light and that can be made manually by use button on car dashboard.

Reset service light indicator, engine oil life Toyota Venza, oil reset instructions:

The oil change system should be reset. Perform the following procedures:

  1. Switch the display to the trip meter A when the engine is running. See below picture.
  2. Vehicles with smart key system: turn the “ENGINE START STOP” switch off. Vehicles without smart key system: turn the engine switch to the “LOCK” position.
  3. Vehicles with smart key system: while pressing the trip meter reset button, set the “ENGINE START STOP” switch to IGNITION ON mode but do not start the engine because otherwise the reset mode will be canceled. Continue to press and hold the trip meter reset button until the trip meter displays “000000”.
  4. Vehicles without smart key system: while pressing the trip meter reset button, set the engine switch to “ON” position but do not start the engine because otherwise the reset mode will be canceled. Continue to press and hold the trip meter reset button until the trip meter displays “000000”.
  5. See below picture with trip meter reset button.

All information how to reset engine oil maintenance indicator is taken from Toyota Venza owners manual.

Maintenance Oil Light Reset Toyota Highlander 2013

Leave a reply

How do you reset maintenance light, reset service light indicator Toyota Highlander, year 2012, 2013, 2014. For reset maintenance light and that can be made manually by use button on car dash board.

Reset service light indicator, engine oil life Toyota Highlander, oil reset instructions:

Vehicles without smart key system

  1. Turn the ignition to run (one position before starting engine).
  2. Ensure Trip Metre A reading is shown. Turn the ignition off. (Go to step 3)

Vehicles with smart key system

  1. Press the “ENGINE START STOP” switch once (do not start engine).
  2. Ensure Trip Metre A reading is shown. Turn the ignition off.
  3. While pressing the Trip Meter reset button, press the “ENGINE START STOP” switch once (do not start engine).
    Without multi-information display: Continue to press and hold the button until the trip meter displays “000000”.
    With multi-information display: Continue to press and hold the button until “COMPLETE” appears on the multi-information display.
  4. Turn the ignition off and then start the engine to verify the indicator has been reset.

Reset tire pressure warning light Toyota Rav4 XA40

Leave a reply

Reset tire pressure warning light Toyota Rav4 XA40 fourth generation. From year: 2013, 2014.

How to reset oil service light Toyota Rav4, 3 generation XA30, 4 generation.

How to initialize the tire pressure warning system.

  1. Park the vehicle in a safe place and turn the engine switch to the “LOCK” position (vehicles without a smart key system) or off (vehicles with a smart key system). Initialization cannot be performed while the vehicle is moving.
  2. Adjust the tire inflation pressure to the specified cold tire inflation pressure level. Make sure to adjust the tire pressure to the specified cold tire inflation pressure level. The tire pressure warning system will operate based on this pressure level.
  3. Turn the engine switch to the “ON” position (vehicles without a smart key system) or IGNITION ON mode (vehicles with a smart key system).
  4. Press and hold the tire pressure warning reset switch until the tire pressure warning light blinks slowly 3 times.
  5. Reset-tire-pressure-warning-light-Toyota-Rav4-XA40
  6. Vehicles without a smart key system: Wait for a few minutes with the engine switch in the “ON” position and then turn the engine switch to the “ACC” or “LOCK” position. Vehicles with a smart key system: Wait for a few minutes with the engine switch in IGNITION ON mode and then turn the engine switch off.

Registering ID codes Toyota Rav 4.

The tire pressure warning valve and transmitter is equipped with a unique ID code. When replacing a tire pressure warning valve and transmitter, it is necessary to register the ID code. Have the ID code registered by your Toyota dealer.

When to replace your vehicle’s tires. Tires should be replaced if:

  • You have tire damage such as cuts, splits, cracks deep enough to expose the fabric, and bulges indicating internal damage.
  • A tire goes flat repeatedly or cannot be properly repaired due to the size or location of a cut or other damage.

If you are not sure, consult with your Toyota dealer.

Replacing tires and wheels (vehicles with the tire pressure warning system).

If the ID code of the tire pressure warning valve and transmitter is not registered, the tire pressure warning system will not work properly. After driving for about 20 minutes, the tire pressure warning light blinks for 1 minute and stays on to indicate a system malfunction.

Tire life Toyota Rav4.

Any tire over 6 years old must be checked by a qualified technician even if it has seldom or never been used or damage is not obvious.

Routine tire inflation pressure checks (vehicles with the tire pressure warning system).

The tire pressure warning system does not replace routine tire inflation pressure checks. Make sure to check tire inflation pressure as part of your routine of daily vehicle checks.

Situations in which the tire pressure warning system may not operate properly (if equipped).

In the following cases, the tire pressure warning system may not operate properly.

  • If non-genuine Toyota wheels are used.
  • A tire has been replaced with a tire that is not an OE (Original Equipment) tire.
  • A tire has been replaced with a tire that is not of the specified size.
  • Tire chains etc. are equipped.
  • Lock nuts are equipped.
  • An auxiliary-supported run-flat tire is equipped.
  • If a window tint that affects the radio wave signals is installed.
  • If there is a lot of snow or ice on the vehicle, particularly around the wheels or wheel housings.
  • If the tire inflation pressure is extremely higher than the specified level.
  • If the spare tire is in a location subject to poor radio wave signal reception.
  • If a large metallic object which can interfere with signal reception is put in

*: Vehicles with a full-size spare tire only

Performance may be affected in the following situations.

  • Near a TV tower, electric power plant, gas station, radio station, large display, airport or other facility that generates strong radio waves or electrical noise.
  • When carrying a portable radio, cellular phone, cordless phone or other wireless communication device.

When the vehicle is parked, the time taken for the warning to start or go off could be extended.
When tire inflation pressure declines rapidly for example when a tire has burst, the warning may not function.

Reset oil service light Toyota Rav4 XA30

Leave a reply

Reset oil service light Toyota Rav4, third generation XA30. From year: 2009, 2010, 2011, 2012, 2013.

How to reset oil service light Toyota Rav4, 3 generation XA30.
To reset the oil change system, follow the procedure below:
Vehicles without smart key system.
  1. Turn the engine switch off with the trip meter A reading shown.
  2. While pressing the trip meter reset button, turn the engine switch to the “ON” position.
  3. Press and hold the button until the trip meter displays “000000”.

 

Vehicles with smart key system.
  1. Turn the “ENGINE START STOP” switch off with the trip meter A reading shown.
  2. While pressing the trip meter reset button, turn the “ENGINE START STOP” switch to IGNITION ON mode.
  3. Press and hold the button until the trip meter displays “000000”.
All information how to reset oil service light is taken from Toyota Rav 4 owners manual.
Used engine oil. Used engine oil contains potentially harmful contaminants which may cause skin disorders such as inflammation or skin cancer, so care should be taken to avoid prolonged and repeated contact. To remove used engine oil from your skin, wash thoroughly with soap and water.
Dispose of used oil and filters only in a safe and acceptable manner. Do not dispose of used oil and filters in household trash, in sewers or onto the ground. Call your Toyota dealer, service station or auto parts store for information concerning recycling or disposal.
Do not leave used engine oil within the reach of children.
 Reset-oil-service-light-Toyota-Rav4-XA30
.
Vehicles without smart key system.
  • The following gauges, meters and displays illuminate when the engine switch is in the “ON” position.
Vehicles with smart key system.
  • The following gauges, meters and displays illuminate when the “ENGINE START STOP” switch is in IGNITION ON mode.
  • Tachometer. Displays the engine speed in revolutions per minute.
  • Speedometer. Displays the vehicle speed.
  • Engine coolant temperature gauge. Displays the engine coolant temperature.
  • Fuel gauge. Displays the quantity of fuel remaining in the tank.
  • Trip information display.
  • Automatic transmission shift position indicator lights.
  • Odometer/trip meter.
  • Odometer. Displays the total distance the vehicle has been driven.
  • Trip meter. Displays the distance the vehicle has been driven since the meter was last reset. Trip meters A and B can be used to record and display different distances independently.
  • Odometer/trip meter switching and trip meter resetting button. Switches between odometer and trip meter displays. Pushing and holding the button will reset the trip meter when the trip meter is being displayed.

Service oil reset Toyota 4Runner

Leave a reply

2005-2009
Turn the ignition to run (one position before starting engine).
Bring up the odometer reading using the trip meter reset knob then the turn ignition off.
Hold down knob while turning the ignition key to the run position (one position before starting engine).
Hold down the knob until the light goes off. Before the light goes off, it illuminates for 3 seconds, flashes for 2 seconds and illuminates for 1 second. If the system fails to reset, the light will remain flashing. In this case, return to step 1 and try again.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2010
Start the engine and bring up the trip meter A reading.
Vehicles with smart key system:
Turn the “ENGINE START STOP” switch off.
While pressing the Trip Meter reset button, press the “ENGINE START STOP” switch once (do not start engine).
Continue to press and hold the button until the trip meter displays “000000”.

1.Turn the ignition off and then start the engine to verify the indicator has been reset.
Vehicles without smart key system:
2. Turn the ignition switch off.
3. While holding down the trip meter reset knob turn the ignition to run (one position before starting engine).
4. Hold down knob for at least 5 seconds. The odometer indicates “000000” and the light goes off. If the system fails to reset, the light will continue flashing.
5. Turn the ignition off and then start the engine to verify the indicator has been reset.