Tag Archives: key

Reset service spanner light Fiat Ducato

Leave a reply

How to reset service wrench light on a Fiat Ducato second edition.

Reset service spanner light Fiat Ducato. From year : 2002, 2003, 2004, 2005, 2006, 2007.

  • Turn ignition to on without starting the engine.
  • Press and hold the button situated in right side of the dashboard.
  • The button must be held down for about 10 seconds until the display shows a spanner and CFG 1.
  • Release the button and then press it again and hold down for about 5 seconds until the CFG1 and wrench key will disappear.
  • Done, you managed to resetservice spanner light Fiat Ducato 2.

Reset tire pressure warning light Toyota Land Cruiser 100 series

Leave a reply

How to reset tire pressure warning light Toyota Land Cruiser 100 series.

Reset tire pressure warning light Toyota Land Cruiser 100 series. From year: 2002, 2003, 2004, 2005, 2006, 2007.

This light comes on when the ignition key is turned to the “ON” position. If the tire pressure warning system works properly and tire inflation pressure is appropriate, the light goes off after a few seconds. This light comes on or flashes in the folowing cases when the ignition key is turned to the “ON” position.

When the low tire inflation pressure is detected while driving.

If any tire has low inflation pressure, the light comes on.

The light goes off after the tire inflation pressure is adjusted to a specified level.

When initializing the system.

If initialization is completed, the light blinks three times.

When the system malfunctions.

If the system malfunctions, the light blinks. Although it is no problem to continue driving, have your vehicle checked by your Toyota dealer as soon as possible.

All information how to reset tire pressure warning light is taken from Toyota Land Cruiser 100 series owners manual.

Reset ABS warning light Toyota Land Cruiser 100 series

Leave a reply

How to reset ABS warning light Toyota Land Cruiser 100 series.

Reset ABS warning light Toyota Land Cruiser 100 series. From year: 2002, 2003, 2004, 2005, 2006, 2007.

The light comes on when the ignition key is turned to the “ON” position. If the anti−lock brake system and the brake assist system work properly, the light turns off after a few seconds. Thereafter, if either of the systems malfunctions, the light comes on again.

When the “ABS” warning light is on (and the brake system warning light is off), the anti−lock brake system, the brake assist system, the vehicle stability control system and/or active traction control system do/does not operate, but the brake system still operates conventionally. When the “ABS” warning light is on (and the brake system warning light is off), the anti−lock brake system does not operate so that the wheels could lock up during a sudden braking or braking on slippery road surfaces.

If either of the following conditions occurs, this indicates a malfunction somewhere in the components monitored by the warning light system. Contact your Toyota dealer as soon as possible to service the vehicle.

  • The light does not come on when the ignition key is turned to the “ON” position, or remains on.
  • The light comes on while you are driving.
  • A warning light turning on briefly during operation does not indicate a problem.

If the “ABS” warning light remains on together with the brake system warning light, immediately stop your vehicle at a safe place and contact your Toyota dealer.

Reset replace key battery message Saab 9-3

Leave a reply

How to reset replace key battery message Saab 9-3 first generation.

Reset replace key battery message Saab 9-3 first generation. From year: 1998, 1999, 2000, 2001, 2002.

 

  • Enter the key in the ignition and turn it until the lights on the dashboard go on, one position befor you start the engine.
  • The replace key battery message light cannot be removed by pressing CLEAR button.
  • To reset this warning light push the brake pedal to clear.

Changing the remote-control battery. When the battery voltage in the remote control falls below a predetermined level the SID will issue the following message: REPLACE KEY BATTERY. Press the CLEAR button on the SID to acknowledge this message. You must then replace the battery without delay to avoid malfunctions. The life of the battery is 4-5 years. After changing the battery you must press the unlocking button of the remote control four times (or until the door locks cycle) while the car is within the range of the remote control in order for the control module to recognize the remote.

Battery for remote control. The battery for the remote control will normally have a life of 4-5 years. When the battery needs changing, ”REPLACE KEY BATTERY” will appear on the SID. After fitting a new battery, press the unlock button on the remote ontrol at least four times in succession, so that the car alarm can recognize the signals from the transmitter. If the remote control has been exposed to very low temperatures, it may not function properly. If this happens, warm it in your hands for a few minutes. If the remote control is not working, it may be because the code signal has not been synchronized with that in the control module for the car alarm. To rectify this, press the unlock button on the remote control at least four times in quick succession. When it is recognized, the door locks will cycle.

Oil reset service light indicator Opel Agila B

Leave a reply

How to reset service light indicator Opel Agila B.

Reset service light indicator Opel Agila B. From years: 2008, 2009, 2010, 2011, 2012.

 

  1. Start with key in, ignition OFF.
  2. Press and hold both buttons (clock button and trip reset button) on the instrument cluster.button.
  3. Turn ignition ON, do not start the car.
  4. Keep holding clock button and trip reset button until on the display will appear InSP message, the indicator will flash three times and change to three dashes “- – – “.
  5. Release the buttons.
  6. Turn ignition OFF.
  7. Turn ignition back ON to confirm that the service light indicator was reset.