Tag Archives: intervals

Timing Belt Warning Indicator Reset Procedure For LandCruiser

Leave a reply

Reset Procedure For Toyota LandCruiser UZJ100, HZJ105 and HDJ100

1. T-BELT MODE DISPLAY
a) With ignition turned ON, using the trip switch (select/reset button) change the display to ODO, and turn the ignition OFF
b) While pressing the trip switch, turn the ignition switch ON and hold it for 5 seconds.
c) Release the trip switch, then press the switch again within 5 seconds.
d) The digital display should change to T-belt mode. The initial display “15” (0,000km) is displayed (ie. 150,000km).

2. REWRITING REPLACEMENT VALUES
While in the T-Belt mode, each press of the trip switch will change the displayed value by 10,000km increments. Once ” 20 ” (200,000km) is reached the display reverts back to ” 1 ” (10,000km) again. Remember, this setting is the number of kilometres to be travelled before the light comes on next, and once reset this counter will start from zero.
I believe the timing belt interval for all the 100 series engine variants is 150,000km, but this should be checked against each different markets servicing recommendation. This being the case, you shouldn’t need to change from the default setting of “15”.
Obviously for the US, the ODO is in miles, and I guess the T-Belt warning would be set in 10,000 mile intervals.

3. T-BELT WARNING RESET COMPLETION
a) After setting the replacement setting value, hold the trip switch ON for more than 5 seconds then release the switch.
b) Check that the display has now changed back to ODO and that the warning light has gone off when the engine is started.
NOTE: If the T-Belt mode is completed, even though the belt replacement has not been performed, the T-Belt warning IS reset.
I hope this proves to be of assistance guys, as usual all care no responsibility. ;-)

Reset oil service light Porsche 911 Carrera

Leave a reply

How to reset oil service light Porsche 911 Carrera.

Reset oil service light Porsche 911 Carrera.

  1. Press inward on the trip odometer reset button and turn the key to the auxiliary position (forward one click from the off position) until Oil Service Re or Oil Service Reset appears on the odometer monitor.
  2. Depress the odometer reset button a second time until the work Reset or Re appears on the monitor.
  3. The message Reset or Re will continuously flash.
  4. Push the odometer reset button quickly to complete the reset.
  5. End SIA appears to indicate a successful reset of the system.

Oil change Porsche 911 Carrera. The engine oil has to be changed regularly at the intervals listed in your Maintenance Schedule.If you suspect an oil leak in the engine have your dealer check it out immediately.
All current engine oils are compatible with each other, i.e. when making an oil change it is not necessary to flush the engine if you wish to use a different brand or grade of oil. Since, however, each brand of oil has a special composition, you should, if possible, use the same oil brand if it becomes necessary to top up between oil changes.
Porsche engines have long intervals between oil changes. You can make best use of these long oil change intervals by using multigrade oils since these are largely independent of seasonal fluctuations in temperature. If your vehicle is used frequently in stop-and-go traffic in cold weather, the engine will not always be properly warmed up. Condensation from products of combustion may accumulate in the oil. In this case, it is advisable to change the oil more frequently so that your engine once again has 100% efficient engine oil.

Reset oil service Skoda 2000

Leave a reply

Skoda 2000

Longlife service intervals require diagnostic tool. Fixed intervals: Press and hold button below the speedometer. Turn ignition to the “ON” position.
“SERVICE” is displayed. Release button. Turn button below the tachometer to the right until display is reset. Turn ignition off.

Oil light reset Jeep Renegade Concept

Leave a reply

Many Jeep vehicles track the intervals between oil changes to alert the driver when the next oil change is needed. A light illuminates on the control panel when the internal system determines it is time for an oil change. Most Jeep mechanics reset the oil light as part of the oil change service. If you change the oil in your Jeep yourself, you can manually reset the oil light. Resetting the oil light after an oil change allows the system to accurately track the time until the next oil change is needed. The procedures described in this article apply to 2010 Jeep models.

Instructions

1.Turn the ignition switch to the “ON” position. Do not start the engine.

2.Press the accelerator pedal completely to the floor slowly three times within a 10-second span.

3.Turn the ignition switch to the “OFF” position.

4.Turn the ignition switch to the “ON” position again. The oil light should be off. If the oil light is still illuminated, repeat the previous steps.

Oil service reset Pontiac Bonneville

Leave a reply

1985-1995

Turn the ignition to run (one position before starting engine).
Press and release the SERVICE REMINDER button until the desired item is displayed.
When the desired item is displayed, do not release SERVICE REMINDER button.
After button has been pressed for approximately 10 seconds, the service interval mileage display will begin to count down in 500 mile/km intervals.
When desired service interval mileage is reached, release button.
Turn the ignition off and then start the engine to verify the indicator has been reset.

1996-1997

Turn the ignition to run (one position before starting engine).
Display the oil life index on the Driver Information Centre.
Hold the RESET button for 5 seconds. When a DIC message of RESET is displayed and the oil life index equals 100%, the reset is complete.
Turn the ignition off and then start the engine to verify the indicator has been reset.

1998

Turn the ignition to run (one position before starting engine).
Press the TRIP button on the Driver Information Centre switch to view various menu choices, stop on OIL LIFE REMAINING.
Press and hold the RESET button on the DIC switch for more than 5 seconds. The oil life will change to 100%. The engine oil life monitor is now reset.
Turn the ignition off and then start the engine to verify the indicator has been reset.

1999

Turn the ignition to run (one position before starting engine).
Press and hold the OIL RESET button in the glove box for at least 5 seconds, but no more than 60 seconds.
After 5 seconds, observe the CHANGE OIL SOON light flash 4 times before light the turns off. This indicates that the engine oil life monitor system has reset.
Turn the ignition off and then start the engine to verify the indicator has been reset.

2000-2005

Turn the ignition to run (one position before starting engine).
Display the oil life index on the Driver Information Centre.
Press and hold the RESET button for more than 5 seconds. The oil life will change to 100%.
Turn the ignition off and then start the engine to verify the indicator has been reset.