Tag Archives: How to reset

Toyota Land Cruiser 200 series reset tire pressure warning light

Leave a reply

How to reset tire pressure warning system Toyota Land Cruiser 200 series.

Reset tire pressure warning light Toyota Land Cruiser 200 series. From year: 2008, 2009, 2010, 2011, 2012, 2013, 2014.

  1. Park the vehicle in safe place and turn the “ENGINE START STOP” switch to OFF mode. While the vehicle is moving, initialization is not performed.
  2. While the vehicle is moving, initialization is not performed. Make sure to adjust the tire pressure to the specified cold tire inflation pressure level. The tire pressure warning system will operate based on this pressure level.
  3. Turn the “ENGINE START STOP” switch to IGNITION ON mode.
  4. Press and hold the tire pressure warning reset switch until the tire pressure warning light blinks slowly three times and the message “TIRE PRESSURE RESET PROCEEDING” appears on the multi-information display.
  5. Wait for a few minutes with the IGNITION ON mode, and then turn the “ENGINE START STOP” switch to OFF mode.
  6. The tire pressure warning valve and transmitter is equipped with a unique ID code. When replacing a tire pressure warning valve and transmitter, it is necessary to register the ID code of tire pressure warning valve and transmitter. Have the ID code registered by your Toyota dealer.

Any tire over 6 years old must be checked by a qualified technician even if they have seldom or never been used or damage is not obvious.

If you press the tire pressure reset switch accidentally.

If initialization is performed, adjust the tire inflation pressure to the specified level and initialize the tire pressure warning system again.

When the initialization of the tire pressure warning system has failed.

Initialization can be completed in a few minutes. However, in the following cases, the settings have not been recorded and the system will not operate properly. If repeated attempts to record tire inflation pressure settings are unsuccessful, have the vehicle inspected by your Toyota dealer.

When operating the tire pressure warning reset switch, the warning light does not flash 3 times and the setting message does not appear on the multi-information display.

Toyota Land Cruiser 100 series Reset unengaged park warning light

Leave a reply

How to reset unengaged park warning light Toyota Land Cruiser 100 series.

Reset unengaged park warning light Toyota Land Cruiser 100 series. From year: 2002, 2003, 2004, 2005, 2006, 2007.

This light warns that the transmission “Park” mechanism is not engaged. If the four−wheel drive control is in the “N” position while the selector lever is in the “P” position, the transmission will disengage and the wheels will not lock.

To restore the park function, shift the four−wheel drive control out of “N”, or the vehicle can move.

All information how to restore the unengaged park warning light is taken from Toyota Land Cruiser 100 series owners manual.

Reset open door warning light Toyota Land Cruiser 100 series

Leave a reply

How to reset open door warning light Toyota Land Cruiser 100 series.

Reset open door warning light Toyota Land Cruiser 100 series. From year: 2002, 2003, 2004, 2005, 2006, 2007.

This light remains on until all the side doors and back door are completely closed.

Below is a picture of how it looks the Toyota Land Cruiser 100 series open door warning light.

Reset-open-door-warning-light-Toyota-Land-Cruiser-100-series

All this information they are taken from Toyota Land Cruiser 100 series owners manual. If the above procedure is not working means that you have damage a sensor. Before you panic check if you have not got the seatbelt in the door.

Reset tire pressure warning light Toyota Land Cruiser 100 series

Leave a reply

How to reset tire pressure warning light Toyota Land Cruiser 100 series.

Reset tire pressure warning light Toyota Land Cruiser 100 series. From year: 2002, 2003, 2004, 2005, 2006, 2007.

This light comes on when the ignition key is turned to the “ON” position. If the tire pressure warning system works properly and tire inflation pressure is appropriate, the light goes off after a few seconds. This light comes on or flashes in the folowing cases when the ignition key is turned to the “ON” position.

When the low tire inflation pressure is detected while driving.

If any tire has low inflation pressure, the light comes on.

The light goes off after the tire inflation pressure is adjusted to a specified level.

When initializing the system.

If initialization is completed, the light blinks three times.

When the system malfunctions.

If the system malfunctions, the light blinks. Although it is no problem to continue driving, have your vehicle checked by your Toyota dealer as soon as possible.

All information how to reset tire pressure warning light is taken from Toyota Land Cruiser 100 series owners manual.

Oil reset service light Mitsubishi Lancer Sportback

Leave a reply

How to reset oil service light Mitsubishi Lancer Sportback (CX_A).

Reset oil service light Mitsubishi Lancer Sportback. From years: 2008, 2009, 2010.

  1. The “- – -” display can be reset while the ignition switch is “OFF”. When the display is reset, the time until the next periodic inspection is displayed and “PERIODIC INSPECTION” is no longer displayed when the ignition is switched from “OFF” to “ON”.
  2. Lightly press the multi-information meter switch until the information screen switches to service reminder display screen.
  3. Press and hold the multi-information meter switch for about 2 seconds or more to display the (wrench icon) and make it flash.
  4. Lightly press the multi-information meter switch while the icon is flashing to change the display from “- – -” to “CLEAR”. After this, the time until the next periodic inspection will be displayed.
  5. Start the engine to verify the indicator has been reset.