Category Archives: Service light reset Mercedes Benz

Oil reset, oil light indicator, maintenance light reset, service light reset, without using a computer for Mercedes Benz

Oil service reset Mercedes Benz SLK – Class

Leave a reply

Reset service light indicator, engine oil life Mercedes Benz SLK – Class, year: 1998-1999, oil reset instructions:

Manual Reset:

1. Turn key in steering lock to position 2.
2. Within 4 seconds press button (1) left of speedometer twice.
3. The present status for days or distance displays
4. Press and hold button (1)
5. Continue to hold button (1) for approximately 10 seconds until a signal sounds and the display shows 10 000 mils or 15 000km. Release button (1).
6. Turn the ignition off and then start the engine to verify the indicator has been reset.
2000-2001
*Diagnostic Reset Tool Required

Manual Reset:

1. Switch ignition on and immediately press knob to left of speedometer twice within 4 seconds.
2. Present status for days or distance is now displayed. Within 10 seconds
3. Press and hold button to the left of speedometer
4. Release button.
5. Service interval displays the reset interval.
6. Turn the ignition off and then start the engine to verify the indicator has been reset.

2002-2004
1. Switch ignition on and immediately press knob to left of speedometer twice within 1 second.
2. Present status for days or distance is now displayed. Within 10 seconds
3. Press and hold button to the left of speedometer
4. Release button.
5. Service interval displays the reset interval.
6. Turn the ignition off and then start the engine to verify the indicator has been reset.

2005-2009
1. Turn the ignition to position 1.
2. Press the system selection button (3 located on the lower left of the steering wheel) repeatedly until the kilometer reading is shown in the multi information display.)
3. Press the cluster illumination button (lower left of instrument panel) quickly 3 times. The battery voltage will be displayed.
4. Press the up or down buttons until the service menu appears.
5. Use the +/- buttons to select menu oprion “”CONFIRM””.”
6. Press the system selection button uuntil “”COMPLETE SERVICE”” is selected.”
7. Confirm “”Complete Service”” with system selection button. The display will show “”SERVICE CONFIRMED””.”
8. Turn the ignition off and then start the engine to verify the indicator has been reset.

2010-2012
1. Turn the ignition to position 1. (close all doors
2. Press the scroll forward button (bottom button on left side of steering wheel controls) to display mileage counter.
3. Press the system selection button (left button on left side of steering wheel controls) repeatedly until the menu item “”trip”” with highlighter is displayed. “”Trip”” remains selected for 5 seconds so move quickly to step 4.”
4. Press and hold accept/end phone button and within 1 second press and hold the button in the center of the arrows (left side of steering wheel). In 5 seconds the Workshop menu will be displayed “”Vehicle data
5. Use scroll forward or backward to highlight “”ASSYST PLUS”” and confirm selection using the button in the center of the arrows. “”Service data”” and “”Full service”” appear in the display.”
6. Use scroll forward or backward to select “”Full service”” and confirm selection with the button in the center of the arrows. The display will show “”Service 1
7. Use scroll forward or backward to select “”Confirm serv”” and confirm selection with the button in the center of the arrows.”
8. Use scroll forward or backward to select engine oil specification used. “”Oil qual. 229.3″” and “”Oil qual. 229.5″” are displayed. Confirm selection with center button. The display shows “”Serv conducted?”””
9. Use scroll forward or backward to select “”Yes”” and confirm with center button. Display will show “”Take-back not possible
10. Use scroll forward or backward until “”Configuration”” is highlighted and confirm selection with button in center of the arrows. “”Full service carried out”” appears in the display.”
11. Use scroll forward and backward to exit menu.
12. Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil service reset Mercedes Benz GLK – Class

Leave a reply

Reset service light indicator, engine oil life Mercedes Benz GLK – Class, year: 2009-2011, oil reset instructions:

1. Turn the ignition to position 1. Ensure mileage is displayed.
2. Press the left arrow repeatedly until the TRIP option is highlighted.
3. Press and hold (phone) button and within 1 second press OK and then hold both buttons for 5 seconds. The shop menu is displayed.
4. Press down repeatedly until “”ASSYST PLUS”” is highlighted and confirm with OK. ”
5. Use the down arrow to select “”FULL SERVICE”” and then confirm with OK. Use the down arrow to select YES and confirm with OK. “”CANNOT BE UNDONE”” displays. Use the down arrow to select CONFIRM and then confirm with OK. The display reads “”FULL SERVICE CARRIED OUT””. Confirm by pressing OK.”
6. Turn the ignition off and then start the engine to verify the indicator has been reset.

Reset maintenance light on dodge sprinter

Leave a reply

Reset service light indicator, engine oil life dodge sprinter, oil reset instructions:

1. Put the key in the ignition and switch it on without starting the engine.
(Wait for LCD to return to the vehicle mileage)
2. Hold the “O” button down till you hear a beep (could take a while, 30 sec.)
3. Press the M button repeatedly and a number of reset menus will appear, (If you have used oil according to quality sheet 229.31 or 228/229.51 you can scroll to Reset.31 or Reset.51 respectively.) Select “reset 51”
4. Now, when appropriate oil type is selected press “O” for 6 seconds until ”2” is displayed.
5. Press “O” once again briefly and the ” reset done” message will confirm that the job is done.
6. Pull the Key out
FOR THE 2004 DODGE SPRINTER!

Turn the key to position 2 in the ignition lock and immediately press the button MI (km) twice.
Within 10 seconds, return the key to the 0 in the ignition lock.
Press and hold the button MI (km). Turn the key to position 2 in the ignition lock. Keep the button MI (km) pressed.
The maintenance indicator with the time/distance is shown.
After about 10 seconds, an acoustic signal will sound and the maintenance indicator is displayed with the new remaining time / distance .
Release the button MI (km)

Reset the Service B in a Mercedes C230

Leave a reply

Reset service light indicator, engine oil life Service B in a Mercedes C230, oil reset instructions:

When a service is needed based on the car’s mileage or time since the last service, the display screen on a Mercedes C230 will notify you. The display screen is located within the speedometer on the instrument panel. Mercedes mechanics will reset the Service B notification light after the service is performed. If you performed the service, you need to reset the light yourself. Service B includes an oil and filter change, a tire rotation and other maintenance checks.

Instructions

1. Insert the key into the ignition and turn it until the battery comes or the engine turns on.

2. Locate the left and right arrow buttons on the left side of your steering wheel. Press either button until the mileage is displayed on the instrument panel display screen.

3. Press the up or down button until the service symbol appears on the screen.

4. Locate the trip odometer reset button to the left of the instrument panel. Hold the reset button for a few seconds until the screen displays the message, “Do you want to reset the service interval? Confirm with the R-button.” Release the button once the phrase appears.

5. Press the reset button to reset the Service B notification.

Reset the Mercedes-Benz SLK 230 for an Oil Change

Leave a reply

Reset service light indicator, engine oil life Mercedes-Benz SLK 230, oil reset instructions:

The Mercedes-Benz SLK 230 features an engine oil-life tracking system as part of the car’s computer. The computer monitors driving habits and engine conditions to determine when the oil needs to be changed. The control panel displays a reminder when the car needs an oil change. In order for the computer system to work correctly to predict the next oil change, reset the light following an oil service.

1. Insert the key in the ignition. Turn the key to position “2.”

2. Press the adjust button twice within one second. The adjust button is located below the speedometer.

3. Turn the ignition off.

4. Press and hold the adjust button. Turn the ignition to position “2.”

5.Release the adjust button after a signal sounds and the service indicator resets visibly.